Effects
Forum rules
You are viewing the Community Help Pages. They are on-line forums where people can come to ask questions about the Smart Photo Editor and all the replies and relevant information are kept in the same place.
You are viewing the Community Help Pages. They are on-line forums where people can come to ask questions about the Smart Photo Editor and all the replies and relevant information are kept in the same place.
5 posts
• Page 1 of 1
- martinhogarth
- Posts: 15
- Joined: Wed Jul 25, 2012 9:57 pm
Effects
by martinhogarth » Fri Feb 18, 2022 2:14 pm
How do I put an effect behind my image instead of in front
Re: Effects
by eadams » Sun Feb 20, 2022 4:02 pm
Can you please phrase your question differently, perhaps with an example? I don't understand what you are asking.
- Richard Briggs
- Posts: 379
- Joined: Thu Sep 19, 2013 12:30 am
Re: Effects
by Richard Briggs » Sat Mar 05, 2022 9:44 am
I assume you are asking the following....
I have my source image loaded.
I create, say, two effects. So now I have my source image and two effects shown top right.
I find that you can move the two effect layers by dragging one left or right so you can change which effect is on top.
However, you can't seem to move the source image anywhere (i.e. to the right). This is a bit like Photoshop's Background Layer I suppose, so no surprises there.
However, I tried reloading my source image as an overlay and that placed a copy far right (i.e. it was now on top). However, I could find no way of dragging that to the left.
I tried reloading the image as an underlay. That presented an interesting image which may be of help to you. However you still couldn't move the reloaded source image left or right.
So, basically, I haven't answered your question! However it does mean I have the same question.
In Photoshop you can't move the background image. But you can make a copy of it to a new layer and that new layer can be moved anywhere in the hierarchy of effect layers you may have. So, is this same mechanism available in SPE? If so, how?
Richard
I have my source image loaded.
I create, say, two effects. So now I have my source image and two effects shown top right.
I find that you can move the two effect layers by dragging one left or right so you can change which effect is on top.
However, you can't seem to move the source image anywhere (i.e. to the right). This is a bit like Photoshop's Background Layer I suppose, so no surprises there.
However, I tried reloading my source image as an overlay and that placed a copy far right (i.e. it was now on top). However, I could find no way of dragging that to the left.
I tried reloading the image as an underlay. That presented an interesting image which may be of help to you. However you still couldn't move the reloaded source image left or right.
So, basically, I haven't answered your question! However it does mean I have the same question.
In Photoshop you can't move the background image. But you can make a copy of it to a new layer and that new layer can be moved anywhere in the hierarchy of effect layers you may have. So, is this same mechanism available in SPE? If so, how?
Richard
Re: Effects
by admin » Mon Mar 07, 2022 10:46 am
I'm still not sure I understand the question. You can certainly put images behind other images in SPE using underlays in the composite panel. I'm not sure what it would mean to apply an effect behind an image as an effect acts on an image and there would be no image to act on.
- Richard Briggs
- Posts: 379
- Joined: Thu Sep 19, 2013 12:30 am
Re: Effects
by Richard Briggs » Mon Mar 07, 2022 8:13 pm
It's me again!
1- I created a pure white image in Photoshop (you can probably do this in SPE).
2 - I loaded it into SPE.
3 - I then applied two effects. By adjusting the opacity of each of the two effects I could create 'artistic' images.
4 - I then loaded my 'SUBJECT IMAGE' as an OVERLAY.
At this stage all you can see is the Subject Image. But you can change this by either...
1 - Varying the opacity of the Subject Image layer or...
2 - Using the masking brush to expose the underlying effects as applied in 3 above.
Richard
1- I created a pure white image in Photoshop (you can probably do this in SPE).
2 - I loaded it into SPE.
3 - I then applied two effects. By adjusting the opacity of each of the two effects I could create 'artistic' images.
4 - I then loaded my 'SUBJECT IMAGE' as an OVERLAY.
At this stage all you can see is the Subject Image. But you can change this by either...
1 - Varying the opacity of the Subject Image layer or...
2 - Using the masking brush to expose the underlying effects as applied in 3 above.
Richard
5 posts
• Page 1 of 1
Who is online
Users browsing this forum: No registered users and 6 guests